The reciprocating rod is replaced by a rotor whose motion is also electrically regulated, by means of tuned parametric resonance (parametric oscillation). The original intent of the patent (electrical regulation of the period (frequency) of a repetitive mechanical motion) is further expanded through subsequent utilization and application of mechanical self‐resonance and radiant energy, in order to make the machine self‐sustaining.

The QEG prototype is scaled to produce electrical power in the range of 10‐15 kW (kilowatts) continuously, with no conventional fuel or input whatsoever, and can be set up to provide either 120 Volt or 230‐240 Volt, 50‐60Hz single phase AC output. We are also planning future designs to provide 3‐phase power.

Service life of the device is limited only by certain replaceable components, such as bearings, v‐belts, and capacitors. The basic machine should operate trouble‐free (with minimal maintenance) for as long as any good quality electro‐mechanical appliance, such as a quality washing machine or refrigerator. Heavy‐duty mechanical components are used throughout for reliability.

The QEG is not a complicated device, as it is designed (like Tesla’s other ‘discoveries’) to work in harmony with nature’s laws, rather than the power wasting closed‐system symmetric motor and generator designs used in today’s mainstream industry.

An effective way to understand the operating principle of the QEG is to think of it as a self‐powered toroidal transformer with high‐voltage primary, and low voltage secondary. The primary high voltage is self‐generated through mechanically pumped parametric resonance. The resonance occurs as a function of the spinning rotor modulating the reluctance/inductance in the primary tank circuit windings. This modulation initiates an oscillation which can develop up to 20,000 volts (20kV) or more in amplitude, with frequency determined by the tank capacitor value and inductance value in the primary windings. Power is then transferred to the secondary windings during the intervals where the rotor is between pole pieces (unaligned). In today’s alternative energy terminology, it would be called a type of resonance machine.

The circuitry that develops high power in this device is based on an existing but under‐utilized power oscillator configuration, with performance enhanced by driving the core steel into resonance. The ‘quantum’ part of the design utilizes the insertion of radiant energy into the generator core to support additional power output. The resultant power output is a combination of radiant and conventional electricity which, depending on tuning, can drive standard loads equivalent to a conventional 10 to 15kW generator (300‐350 Volts, at up 30 Amps or more).

Due to the Lenz effect, conventional alternators (AC generators) consume much more input power than the output power they provide. For example, one brand of power take off (PTO) alternator uses 18,000 watts (24 horsepower) to develop 13,000 watts of output power. In the QEG, input power is used only to maintain resonance in the core, which uses a fraction of the output power (under 1000 watts to produce 10,000 watts), and once development is completed, the QEG will provide this power to its own 1 horsepower motor. This is known as over‐unity, or COP over 1 (Coefficient of Performance). Once the machine is up and running at the resonant frequency, it will power itself (self‐sustaining).

Multiple Order Harmonics: Tuning The QEG 

2017 Energy Science and Technology Conference Presentation

James Robitaille (preview below)

LEARN MORE: MULTIPLE ORDER HARMONICS 

The post What is the Quantum Energy Generator (QEG)? appeared first on Clean Energy Academy.

The QEG is not a scam. The QEG is an open sourced project that is in co-development with various teams of people around the world. It is based on technology that was invented by Nikola Tesla and suppressed for 130 years. Many engineers see the electrical potential of this different form of energy production and are eager to experiment and learn. There are over 100 QEG’s that are actually physically being built in over 40 countries.  Some of the people who are building QEGs come from backgrounds such as NASA, Lockheed Martin, Los Alamos Laboratories and the United Nations.

The nature of the QEG project makes it one of the biggest threats to the oil industry. Because of this, we receive more controlled opposition, and suppression attacks than any other free energy device on the planet.

Suppression of new forms of energy production is very real and has a long dark history. Energy companies and government agencies have employed people to create websites and rumors that the QEG is a scam in an effort to control public opinion to believe that such technology is not real so that we will all keep paying our utility bills for a 600 trillion dollar industry.  These statements are not just opinions, they are based in facts with mountains of evidence to support them.  Please read our full report: “What you need to know about Internet Trolls and Free Energy Debunkers” for more details.

The QEG is a grassroots project that is being carried out by average people and engineers who are trying to help further the technological advancement of our human condition, and free us from the control of the energy industry.

The post Is the QEG a scam / hoax? appeared first on Clean Energy Academy.

One of the questions people ask is “Does the QEG free energy violate the laws of physics? The QEG is an asymmetrical open system that operates according the laws of nature. It does not violate the laws of thermodynamics (physics) as these only apply to a closed symmetrical system. Asymmetrical open systems have been traditionally omitted from higher educational learning programs, so your university instructor does not know about them and assumes they don’t exist.

MAXWELL, EDISON, JP MORGAN AND THE LAWS OF PHYSICS

James Clerk Maxwell FRS FRSE (1831–1879) was a Scottish mathematical physicist. His most prominent achievement was to formulate a set of equations that describe electricity, magnetism, and optics as manifestations of the same phenomenon, namely the electromagnetic field. His discoveries helped usher in the era of modern physics, laying the foundation for such fields as special relativity and quantum mechanics. In his ORIGINAL work: The Dynamical Theory of the Electromagnetic Field, Maxwell identified two separate systems, both of which were completely different from each other:

1)Asymmetrical system – an ‘open’ system that allows the creation of a series of exchange of energy reaction to our inputs, based on electromagnetic resonance or electromagnetic feedback in every spin (on a motor), or in every pulse of input in a static coil. One of the first asymmetrical motors was Faraday’s ‘Unipolar Motor,’ later modified by Nikola Tesla. These systems generate their own energy and do not require fossil fuels.

2) Symmetrical system – a ‘closed’ system that cancels the electromagnetic resonance with every spin, which creates wasted energy in excessive heat and requires an additional energy source to run such as fossil fuels. These are the “symmetrical obsolete systems” we use every day in all of our electrical appliances.

One year after Maxwell’s death in 1879, scientists Hendrick Lorentz financed by J.P. Morgan and Thomas Edison, mutilated Maxwell’s original work and spent the next two decades deleting all knowledge of asymmetrical systems that would not require the profitable oil industry to operate. They ‘symmetrized’ all of Maxwell’s equations, and labeled these incomplete theories as the “Laws of Physics”. While the laws of physics do indeed apply to symmetrical closed systems of energy, there is another set of laws: The Laws of Nature, which apply to the asymmetrical systems that have been suppressed by the financial interests of the banking families for the last 130 years.

This knowledge was banned from our educational system, and no physics or electrical engineering school on our planet would ever teach about asymmetrical systems. Instead, the first and second laws of thermodynamics, which depend on the consumption of profitable fossil fuels, would conveniently prevail in our public knowledge base.

THE FLIGHT OF THE BUMBLEBEE AND THE LAWS OF NATURE

The laws of physics tell us that perpetual motion is not possible, yet how does the earth rotate? The laws of aerodynamics tell us that bumblebees are incapable of flight, yet how do they fly?

Conventional scientists from all over the world will make statements such as: “The claim that this is going to run permanently or indefinitely doesn’t seem to hold because the second law of thermodynamics tells us that this is not possible.”

Around the turn-of-the-century eminent British scientist Lord Kelvin said “Radio has no future, heavier-than-air flying machines are impossible, and x-rays are a hoax” – so much for conventional science.

The laws of nature contain concepts that focus on frequency, resonance, vibration, magnetics and energy. A perfect example of this can be found in the aerodynamics-law-breaking flight of the bumblebee.

Ralph Ring is an innovative technician who worked with Otis T. Carr, a direct apprentice of Nikola Tesla. In his presentation at the Breakthrough Energy Movement Conference, Mr. Ring gives an amazing explanation of the flight of the bumblebee:

“Next to the larynx in the bumblebee’s throat, there is a tiny hollow tube that acts as a resonance cavity that accumulates frequency. When the bee starts beating its wings, it does this to accumulate frequency which bounces back and forth in the resonator cavity until it reaches the same frequency of the earth, known as the Schumann frequency. Once the bee reaches the same frequency as its surroundings it evens out into what is known as zero point. When anything reaches zero point you can then change the energy. The bee is now free from the gravitational influence around it, creates its own little magnetic bubble and hovers around. There are some lizards and hummingbirds that do the same thing.”

This is how the laws of nature work. When you can tune something to vibrate at the same frequency as the earth and reach zero point, you are freed from the frequency influence of your environment and can then change the energy into anything you want including levitation or electrical energy.

This is how the QEG works: Tesla’s design causes it to resonate so that it matches the frequency of the earth, and in zero point it changes the energy into self-renewing electrical energy.

For More information, please view this video on why they don’t teach free energy tech in schools and decide for yourself the answer to the question “Does the QEG free energy violate the laws of physics?”

The post Does the QEG Free Energy Violate the Laws of Physics? appeared first on Clean Energy Academy.

Once tuned, the QEG’s sinusoidal output energy is a combination of AC, RF, and radiant impulses, which will drive standard loads equivalent to 3kW (guaranteed) up to 10kW RMS or more, depending on the level of tuning. The output frequency I’m running is 150Hz, which is the ½ harmonic of the M19 core steel’s resonant frequency of 300Hz (this may be different for your machine depending on steel type used), and this is the frequency (150Hz) that has to be converted to 50 or 60HZ to be usable as your electrical mains. The output voltage is dependent upon whether the secondary output is wired in series or parallel, and will likely be 300-350 VAC for series wiring, and 150-200 VAC for parallel. Since people seem to expect a COP rating (which is really inappropriate for a self-sustained machine), I have guaranteed output of at least COP 3.9 based on the ratio of motor input power (768 Watts or 1 HP) to total output power (3000/768=3.90625), or at least 3kW RMS output.

How much power does a QEG produce? The QEG Tuning Video (3hrs) explains the tuning procedure and how to increase the power output on the QEG:

The post How Much Power Does a QEG Produce? appeared first on Clean Energy Academy.

We get asked this question a lot, “Is there a video of a self running QEG?” So we thought we would publish our answer: After some tough lessons about the unsavory things that go on in this ‘free energy’ arena, which we had no idea about when we began in 2013, we must inform you that no videos demonstrating overunity, self-sustaining, or live electrical measurements will be forthcoming from us. There are very good reasons for this which will be explained below. The faithful people who are successfully building, doing the work and following our instructions can demonstrate their machines if they so desire.

It’s a funny thing how many are coming out of the woodwork now that we have done all the work, who want us to ‘prove it’ to them, but we have been wisely advised over the past several months – as we were reaching our breakthrough – to never, EVER make any promises of financial return or ‘proof’ of technological success. Even WITTS told us their demo videos have done them little good since people simply assume they are fake, and as such, become more fodder for condemnation. The QEG family has lost enough just by posting all instructions freely on the internet, and we have been publicly beaten up by the naysayers, shills, and trolls quite enough.

Historically, those who have been successful in anything that goes up against Big Energy have had their reputations, labs, and lives destroyed, and have even been murdered. We have been very public up to now because we felt it was our only protection. It’s tempting, but we draw the line at demonstrations, as this is where bad things start to happen to good people.

We know this is disappointing, but we have been put up against a wall by those who have their own agendas for control of this splendid technology. We are not manufacturers of QEGs, we are teachers. We are not selling a product, we are sharing technology and asking for compensation for our time. We must maintain our stand.

For more information about why we don’t show a video of a self running QEG, please watch the following short video:

The post Is there a video of a self running QEG? appeared first on Clean Energy Academy.

The QEG is a prototype, which means it is still in development and we cannot definitively answer the question “how much does a QEG cost?” There is not yet a fixed price for a finished product. Any skilled engineer can use the free open sourced QEG manual to source all the different components from various suppliers around the world.  To help answer this question, we can provide the cost data that we have experienced through building 6 QEG’s in different locations.

To build a QEG you’ll need to purchase all the parts, have a workspace to build, and have a variety of mechanical tools for testing and measuring. The cost for the space and the tools may vary. A list of helpful tools has been provided in the QEG course documents.

Cost for parts:

We spent between $6,000- $8,000 just for the parts for each QEG we built. This does not include shipping, tools or other project expenses. We have put together an expenditures report that fully outlines all expenses of the project. We estimate that with further co-development this cost can be significantly reduced. However, we have not yet reached that industry level of development yet.

Buying a Core:

You can have a company make your core for you and wind it yourself, your costs will vary.  We have a working relationship with a small company in the US called Torelco that will create a fully processed core for you and ship it. The price for a Torelco Core is $3,095 this does not include shipping. Torelco will ship anywhere in the world.

Torelco will shortly be supplying kits with the rest of the parts needed for around $3200.

For more information on some of the experiences the QEG family has had with funding the QEG project, please watch the following video:

The post How much does a QEG cost? appeared first on Clean Energy Academy.

We often get asked the question: “Where can I buy a QEG?” You cannot buy a ready made QEG from a supplier yet, you will need to build one yourself or hire someone to build one for you. You can use the manual to source the parts yourself or you can purchase the core and kit from Torelco. The FTW organization does not sell QEG’s, we build prototypes and teach others how to build through educational materials.

ORDER QEG PARTS FROM TORELCO!

Torelco offers a fully processed core and supplemental kit to complete your QEG generator, or you can buy parts separately. (The photo above depicts an epoxied core. Non-epoxied cores are also available.)

Please refer to the QEG Build Manual  for detailed descriptions and photos of parts listed below.

 
Processed Core (delivered):

Generator Core, 12″ OD X 6″ ID, 15″ overall, 3-1/2″ stack, 84 lbs.
Spacer Blocks, Aluminum 6061-T6, 1-1/2″ X 1-1/2″ X 4-1/2″
Mica Tape, VonRoll 77956 Mica Mat, Polyester Resin Bonded 1″
Mica Plates, 2.25″ X 4.5″ X .030″, ‘C’ shape, prefabricated
Nomex corner insulation, hand cut
Tape, black, 1″ reinforced, high-strength
Sleeving, fiberglass w/PVC, for magnet wire
Tubing, Teflon, for #20 HTAIHSD
Tubing, Teflon, for #12 HTAIHSD
Magnet wire, HTAIHSD #20 RD NAT REA – Pulse Shield – Heavy MW35, 73, 36
Magnet wire, HTAIHSD #12 RD NAT REA – Pulse Shield – Heavy MW35, 73, 36
Tape, white, 1″ fiberglass, hi-temp
2X4s, plywood, misc. shipping pallet materials
Core complete. Processed and secured for shipping

Parts Kit Description (1 system):

7/8″ Shaft
Bonding Compound #648 50 ml
Primer/Activator #7471 4.5 oz.
Bearings
Bearing Hardware Kit
End Plates
End Plate Hardware Kit
Shrouds
Shroud Hardware Kit
V-Belt 4L430
Pulley AK30 x 7/8
Pulley AK25 x 7/8
DC PM Variable Speed Motor 90/180V Armature
Motor Mounting Hardware Kit
Variac – Staco 1520CT
Bridge Rectifier
Switch
Capacitors 940C30P15K-F
Terminal Lug T&B L70
Drill Rod, 1/4″ [6.35mm]Ø, Type A2, 1-1\8″ L
Platform (Base), Laminate, 18″ x 36″ x 1-1/2″
Core Mounting Shoe, Laminate, 15″ x 6-1/2″ x 1-1/2″
Core Mounting Shoe Hardware Kit
Exciter Coil Assembly

Torelco is working with FTW on best pricing and accessibility of parts available. Please contact Matt Peterson at mpeterson@torelco.com and include “QEG” in the subject line so we can expedite your order.

We are happy to provide this service and thank you for your patience in awaiting a reply to your inquiries.

See Torelco Winding Company QEG Cores and Parts in Action in the video below:

FTW builds QEG prototypes and teaches QEG technology to other engineers. FTW offers educational materials and consulting services to independent groups that are building QEG’s.
FTW does not sell QEG’s, mass manufacture QEG’s, or play a decision making role in any small business group that does.

The post Where Can I Buy a QEG? appeared first on Clean Energy Academy.

We cannot guarantee that there will be no attempt to suppress the QEG by the controlling corporations and governments. When asked the question; “is it safe to build a QEG free energy generator?” we can report that we have implemented a strategy different than those that have been tried before us to help this break through the suppression. All other legitimate free energy devices that have been developed in the last few decades have been stopped from getting out to the public through traps such as:

1) Patents: the US Patent office confiscates them and forbids the inventor to invent.

2) Secrecy: non-disclosure agreements ensure that only a handful of people know about a technology, and therefore it is easier to suppress

3) Greed: promises of great financial wealth are made (and usually never fulfilled) to manipulate the inventors, keep a device secret and under ownership, and therefore easy to control and suppress.

4) Governmental laws in “police state” countries. In some countries, the governments are attempting to make it illegal for individuals to create their own power. Laws, codes, fines and regulations around this subject are found predominantly in the “Five Eyes Countries”: USA, UK, Canada, Australia, New Zealand.

The strategy that FTW is implementing is an attempt to thwart these common traps of suppression in an effort to get this device (and others like it) directly into the hands of the people so that it can become a new common standard of energy use.  Our strategy is being implemented in the following ways:

1) Open source: No patents, as this device is based on a patent that is in the public domain. Therefore there is no ownership and anyone with the skills can build one without copyright infringement or patent confiscation.

2) Public promotion and full transparency: we do not operate under secrecy or non-disclosure agreements and all information about the device and our research is publically reported on the internet. We have used the viral nature of the internet and social media to ensure that millions of people know about the QEG and are following the progress of the project. (As of July 12th, 2015, development of the QEG prototype is private, i.e., we no longer provide reports to the public going forward, or fight back the trolls, and we will no more go broke to prove anything at our own family’s expense and safety.)

3) Crowdfunding: 1,212 people have contributed to help pay for the expenses of the QEG project. This eliminates the risk, and ability to control by any single funding entity.

4) Grassroots: We have implemented the QEG on a grassroots level with individuals around the world. Social media and the internet works fast, governments do not. This way people have direct access to this technology and this project which minimizes governmental interference.

The open sourcing of the QEG project done through the internet by a small family with pure intentions was an unexpected move according to the controlling powers of this world. We have endured a lot to protect the integrity of this project. To date, the QEG project has experienced suppression attempts in the following ways:

– The QEG is a targeted project for government paid trolls and “free energy de-bunkers” that protect the corporate energy industry. We have witnessed many online paid troll activities that specifically target the QEG and our family.

-We have received many online empty threats by anonymous psychopathic individuals.

– During the various QEG builds we attended, we were approached by many individuals representing various groups with ulterior motives and dark agendas. These mostly involved promises of wealth, fame and power in exchange for control of the project. Most of these individuals dissolved their relationship with the QEG (or were re-assigned to other projects) when they realized that our strategy of open sourcing, crowdfunding and co-development makes it almost impossible to buy, own or control the project.

For more information on the dangers of Patenting a Free Energy Device please enjoy this video:

The post Is it safe to build a QEG free energy generator? appeared first on Clean Energy Academy.